Select a New System

Available as single-zone or multi-zone units, FH models include high end features enabled by the 3D i-see SensorTM such as occupancy detection, direct mode and indirect mode. Whisper-quiet operation as low as 20 decibels eliminates unnecessary noise while air filters eliminate unwanted smells, particulates and allergens.

• This model has a heating mode to ensure optimal comfort when your home isn't warm enough.
• This model has a cooling mode, allowing you to achieve precise temperature control during warm periods.
• This model is equipped with the i-see Sensor™ and responds to troublesome regions closer to the ceiling and the floor.
• This model has multi-stage allergen filtration, removing particulates and contaminants from the air.
• This model uses Hyper-Heating INVERTER™ technology to offer exceptional performance down to 13 degrees outdoor ambient.

Slim and compact, INVERTER-driven compressor, quiet, Pulse Amplitude Modulation (PAM), A-control connection, hyper-heating performance, blue fin coating on outdoor unit Available as a heat pump or an H2i® hyper-heating heat pump, each outdoor unit is capable of connecting up to eight indoor units. These outdoor units have INVERTERdriven compressors that only use the precise amount of energy needed to keep the space comfortable.

• This model has a heating mode to ensure optimal comfort when your home isn't warm enough.
• This model has a cooling mode, allowing you to achieve precise temperature control during warm periods.
• Some units offer Hyper-Heating INVERTER™ technology
• Up to 8 zone heating and cooling

With compact designs, and a wide-range of available sizes, the GL model of wall-mounted units keep rooms of nearly any size comfortable. The GL model includes the MSZ-GL heat pump which is available as a single-zone or multi-zone unit and the MSY-GL, a single zone, cooling only unit for climates where heating is unnecessary. At 19 decibels, the GL model has the lowest noise levels in the industry

• Wall-mounted units independently manage the comfort of a single room and can maintain the precise temperature you set.
• Advanced filtration features deodorize and purify the air in your home, contributing to better health.

These outdoor units have INVERTER-driven compressors that only use the precise amount of energy needed to keep the space comfortable.

• This model has a heating mode to ensure optimal comfort when your home isn't warm enough.
• This model has a cooling mode, allowing you to achieve precise temperature control during warm periods.
• This model uses Hyper-Heating INVERTER™ technology to offer exceptional performance down to -13? F outdoor ambient, with 1

These slim, floor-mounted units can be mounted partially recessed into the wall. Best used in a home, store or restaurant space, this is a great option if you are replacing radiators or want a unit in your sunroom or attic. Available as single-zone and multi-zone models, these units are equipped with H2i Hyper-Heating® technology, rapid heating capabilities and a multi-flow vane to control airflow throughout a space.

• Auto Changeover: automatically switches between heating and cooling modes to maintain the desired temperature
• Auto Restart: especially useful at the time of power outages, the unit turns back on automatically when power is restored
• Weekly Timer: easily set desired temperatures and operation ON/OFF times to match your lifestyle
• On/Off Timer: use the remote controller to set the times of turning the unit on and off
• Low-temperature Cooling: intelligent fan speed control on P-series outdoor units that ensures optimum performance.

These outdoor units have INVERTER-driven compressors that only use the precise amount of energy needed to keep the space comfortable.

This basic heat pump is available as a single-zone unit and keeps operating noise as low as 22 decibels.

• This model has multi-stage allergen filtration, removing particulates and contaminants from the air.

These outdoor units have INVERTER-driven compressors that only use the precise amount of energy needed to keep the space comfortable.

The extraordinary Trane Hyperion™ air handler represents a substantial advance in air handling technology. Using 14 industry-exclusive patents, the Hyperion offers significant advantages over other air handlers, advantages like refrigerator-styled insulation made without exposed fibrous material, which virtually eliminates sweating and condensation as well as helping create a safer environment for your home.

• Uniquely designed cabinet
• Fully enclosed insulation
• All-aluminum coil
• Unique modular design
• Quick-turn fasteners
• No leak drain pan made from rust-resistant composites and built with a gradual slope
• Heating options for either hydronic or electric heat
• Corrosion-resistant finish

More speeds, more comfort This system gives you comfort by running at the speed your home needs to stay comfortable. This allows the variable speed compressor, outdoor fan, and indoor fan to vary their speed as the temperature outside changes, slowing down or speeding up gradually when needed.

• Variable-speed fan motor
• Woven Spine Fin™ coil
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

The extraordinary Trane Hyperion™ air handler represents a substantial advance in air handling technology. Using 14 industry-exclusive patents, the Hyperion offers significant advantages over other air handlers, advantages like refrigerator-styled insulation made without exposed fibrous material, which virtually eliminates sweating and condensation as well as helping create a safer environment for your home.

• Uniquely designed cabinet
• Fully enclosed insulation
• All-aluminum coil
• Unique modular design
• Quick-turn fasteners
• No leak drain pan made from rust-resistant composites and built with a gradual slope
• Heating options for either hydronic or electric heat
• Corrosion-resistant finish

One of the best on the market This heat pump is one of the industry’s most efficient systems, with ratings up to 18 SEER2 and 8.5 HSPF2. With Trane TruComfort™ technology, the XV18 automatically adjusts itself to keep you comfortable.

• Woven Spine Fin™ coil
• Variable-speed fan motor
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

The M Series air handlers combine affordability and flexibility to work with the complete range of Trane heating and cooling products. So you get the reliability of Trane and the options to work within your specific system and budget. TEM6 model features a variable speed motor and Comfort-R technology for more efficient home comfort.

• 4-way convertible line
• Galvanized steel cabinet
• Optional electric heat
• All-aluminum coil
• No-rust polymer drain pan
• Cooling and heat pump systems available

Choose your speed Two-stage heat pumps use in two speeds to keep your home comfortable all year long. Our two-speed units provide an excellent mix of value, comfort, and efficiency.

• Spine Fin™ Coil
• WeatherGuard™ top

The TEM4 air handler combines affordability and flexibility to work with the complete range of Trane heating and cooling products. So you get the reliability of Trane and the options to work within your specific system and budget. For small area applications, this affordable air handler meets or exceeds all standard efficiency requirements.

• The TMM and GMU/V air handlers are Upflow Only for use in wall, stud, or over the water heater applications.
• Standard convertible line
• Galvanized steel cabinet
• Optional electric heat
• All-aluminum coil
• No-rust polymer drain pan
• Cooling and heat pump systems available

The heating and cooling reliability you expect from Trane and the energy efficiency you deserve is available with these 2.5-ton to 5-ton heat pumps. The XR15 electric heat pump offers up to a 16.00 SEER rating when matched with Trane variable speed air handlers, furnaces and Comfort Coils™.

• Galvanized-steel louvered panels
• Baked-on powder paint
• Corrosion-resistant Weatherguard™ fasteners
• Spine Fin™ coil
• Sound insulator on compressor (on select models)

The extraordinary Trane Hyperion™ air handler represents a substantial advance in air handling technology. Using 14 industry-exclusive patents, the Hyperion offers significant advantages over other air handlers, advantages like refrigerator-styled insulation made without exposed fibrous material, which virtually eliminates sweating and condensation as well as helping create a safer environment for your home.

• Uniquely designed cabinet
• Fully enclosed insulation
• All-aluminum coil
• Unique modular design
• Quick-turn fasteners
• No leak drain pan made from rust-resistant composites and built with a gradual slope
• Heating options for either hydronic or electric heat
• Corrosion-resistant finish

With Trane TruComfort™ variable speed technology, the XV20i continuously adjusts its speed to meet the temperature you desire. It gradually slows down or speeds up to deliver a consistent flow of cool, comfortable air.

• Compressor Sound Insulator
• Woven Spine Fin coil
• Variable-speed fan motor
• Swept fan blade
• ComfortLink II capability
• Simplified Two-Wire Connection

The extraordinary Trane Hyperion™ air handler represents a substantial advance in air handling technology. Using 14 industry-exclusive patents, the Hyperion offers significant advantages over other air handlers, advantages like refrigerator-styled insulation made without exposed fibrous material, which virtually eliminates sweating and condensation as well as helping create a safer environment for your home.

• Uniquely designed cabinet
• Fully enclosed insulation
• All-aluminum coil
• Unique modular design
• Quick-turn fasteners
• No leak drain pan made from rust-resistant composites and built with a gradual slope
• Heating options for either hydronic or electric heat
• Corrosion-resistant finish

The 17.2 SEER2 rating makes this air conditioner energy-efficient while providing home comfort.

• Full-side louvered panels
• Spine Fin™ coil
• Swept fan blade

The M Series air handlers combine affordability and flexibility to work with the complete range of Trane heating and cooling products. So you get the reliability of Trane and the options to work within your specific system and budget. TEM6 model features a variable speed motor and Comfort-R technology for more efficient home comfort.

• 4-way convertible line
• Galvanized steel cabinet
• Optional electric heat
• All-aluminum coil
• No-rust polymer drain pan
• Cooling and heat pump systems available

Two-stage cooling with the Trane XL16i offers flexible family comfort, with the ability to cool every room to the right temperature efficiently. So even the hard-to-cool parts of your home will be easy to relax in.

• Spine Fin™ coil
• Swept fan blade

The TEM4 air handler combines affordability and flexibility to work with the complete range of Trane heating and cooling products. So you get the reliability of Trane and the options to work within your specific system and budget. For small area applications, this affordable air handler meets or exceeds all standard efficiency requirements.

• The TMM and GMU/V air handlers are Upflow Only for use in wall, stud, or over the water heater applications.
• Standard convertible line
• Galvanized steel cabinet
• Optional electric heat
• All-aluminum coil
• No-rust polymer drain pan
• Cooling and heat pump systems available

The 14.8 SEER2 rating balances energy efficiency and cooling strength to help lower your home cooling costs.

• Spine Fin™ coil

The XL16c is a high-efficiency, all-electric heat pump, maximizing your comfort whatever the season, year after year. The packaged heating and air conditioning system is all contained in one sleek cabinet for optimal use in any home.

• The variable-speed Vortica™ blower motor with Comfort R™ will deliver the sustained performance.
• Single and 3-phase
• Tough corrosion and UV resistant paint
• Ultra quiet Performance
• State-of-the-art fan system

With durable components assembled into one cabinet, the XL15c packaged heat pump system delivers exceptional heating, cooling and quiet operation, all at the same elevated efficiency you expect from Trane.

• Variable-speed indoor blower motor
• Single phase only
• Composite Vortica™ blower
• Tough corrosion and UV-resistant paint
• Demand defrost
• Ultra quiet

The Trane XR14c heat pump package unit features an electric heat pump combined with a powerful airflow system to make sure every corner of your home will be efficiently comfortable.

• All-Aluminum Spine Fin™ Coil
• Tough corrosion and UV-resistant paint
• Advanced Vortica™ blower motor
• Rugged, all-steel cabinet
• Electronic Demand Defrost
• Advanced airflow system for quiet and efficient outdoor operation

The XR14h all-in-one heating and cooling units are designed to work efficiently and quietly to keep your home cool and comfortable year round. Packaged in a flexible cabinet, the XR14h all-in-one heating and air conditioning systems suit the structural and spatial requirements of your home.

• Appliance-Grade Finish
• Electronic Demand Defrost
• Direct-drive two-speed blower motor

With durable components assembled into one cabinet, the XL15c packaged air conditioner system delivers exceptional cooling, all at the same elevated efficiency you expect from Trane.

• Variable-speed indoor blower motor
• Comfort-R™ mode
• Spine Fin™ condenser
• Single phase only
• Climatuff® compressor
• Composite Vortica™ blower
• Ultra quiet

The Trane XR14c features a stainless steel heat exchanger. Combined with a powerful airflow system, it makes sure every corner of your home will be efficiently cool and comfortable.

• Spine Fin™ condenser
• Single phase
• Composite Vortica™ blower
• Microchannel evaporator coil on 2–4 ton

The S9V2-VS furnace is a high efficiency two stage furnace that achieves 97% gas efficiency (AFUE). It features both a variable speed draft inducer and our patented Vortica™ II variable speed blower motor, to bring you and your home comfort and efficient performance

• Variable-speed ECM blower motor
• Variable-speed draft inducer
• Comfort-R™ mode
• Single or two pipe vent options
• 40-120 mbth input
• Two-stage heat
• Fully insulated/gasketed
• Silicon nitride ignitor
• Standard 34″ height
• IFC boatd with digital configuration, status and fault codes
• Certified to 2% air leakage

With Trane TruComfort™ variable speed technology, the XV20i continuously adjusts its speed to meet the temperature you desire. It gradually slows down or speeds up to deliver a consistent flow of cool, comfortable air.

• Compressor Sound Insulator
• Woven Spine Fin coil
• Variable-speed fan motor
• Swept fan blade
• ComfortLink II capability
• Simplified Two-Wire Connection

The S9V2 furnace boasts an impressive 96% AFUE, making it one of the most efficient furnaces in the industry. Sit back, stay warm, and enjoy lower utility use in the winter and summer.

• Comfort-R™ mode
• Two-speed inducer
• Single or two pipe vent options
• 40–120 mbth input
• Two-stage heat
• Dry contact Humidifier and EAC terminals
• Fully insulated/gasketed
• Silicon nitride igniter
• Standard 34″ height
• IFC board with digital configuration, status and fault codes
• Certified to 2% air leakage

The 17.2 SEER2 rating makes this air conditioner energy-efficient while providing home comfort.

• Full-side louvered panels
• Spine Fin™ coil
• Swept fan blade

The S9X1 furnace offers a high-efficiency constant torque ECM blower motor for comfort in cold weather, while maintaining the DNA that Trane is known for: quality and reliability. The S9X1 is rated at up to 96% gas efficiency (AFUE), providing energy savings and a consistent flow of warm, comfortable air in both winter AND summer.

• Self-diagnostic integrated furnace control board (IFC)
• Matches with single- and two-stage AC and HP for more system options
• Sealed combustion, 100% outside air option
• Multi-port, in-shot burners
• Tubular, stainless steel primary heat exchanger
• Patented Vortica™ II blower design
• Pre-painted galvanized steel cabinet
• Fully insulated for quiet operation

Two-stage cooling with the Trane XL16i offers flexible family comfort, with the ability to cool every room to the right temperature efficiently. So even the hard-to-cool parts of your home will be easy to relax in.

• Spine Fin™ coil
• Swept fan blade

The S9X1 furnace offers a high-efficiency constant torque ECM blower motor for comfort in cold weather, while maintaining the DNA that Trane is known for: quality and reliability. The S9X1 is rated at up to 96% gas efficiency (AFUE), providing energy savings and a consistent flow of warm, comfortable air in both winter AND summer.

• Self-diagnostic integrated furnace control board (IFC)
• Matches with single- and two-stage AC and HP for more system options
• Sealed combustion, 100% outside air option
• Multi-port, in-shot burners
• Tubular, stainless steel primary heat exchanger
• Patented Vortica™ II blower design
• Pre-painted galvanized steel cabinet
• Fully insulated for quiet operation

The 14.8 SEER2 rating balances energy efficiency and cooling strength to help lower your home cooling costs.

• Spine Fin™ coil

The S9V2-VS furnace is a high efficiency two stage furnace that achieves 97% gas efficiency (AFUE). It features both a variable speed draft inducer and our patented Vortica™ II variable speed blower motor, to bring you and your home comfort and efficient performance

• Variable-speed ECM blower motor
• Variable-speed draft inducer
• Comfort-R™ mode
• Single or two pipe vent options
• 40-120 mbth input
• Two-stage heat
• Fully insulated/gasketed
• Silicon nitride ignitor
• Standard 34″ height
• IFC boatd with digital configuration, status and fault codes
• Certified to 2% air leakage

More speeds, more comfort This system gives you comfort by running at the speed your home needs to stay comfortable. This allows the variable speed compressor, outdoor fan, and indoor fan to vary their speed as the temperature outside changes, slowing down or speeding up gradually when needed.

• Variable-speed fan motor
• Woven Spine Fin™ coil
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

The S9V2 furnace boasts an impressive 96% AFUE, making it one of the most efficient furnaces in the industry. Sit back, stay warm, and enjoy lower utility use in the winter and summer.

• Comfort-R™ mode
• Two-speed inducer
• Single or two pipe vent options
• 40–120 mbth input
• Two-stage heat
• Dry contact Humidifier and EAC terminals
• Fully insulated/gasketed
• Silicon nitride igniter
• Standard 34″ height
• IFC board with digital configuration, status and fault codes
• Certified to 2% air leakage

One of the best on the market This heat pump is one of the industry’s most efficient systems, with ratings up to 18 SEER2 and 8.5 HSPF2. With Trane TruComfort™ technology, the XV18 automatically adjusts itself to keep you comfortable.

• Woven Spine Fin™ coil
• Variable-speed fan motor
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

The S9X1 furnace offers a high-efficiency constant torque ECM blower motor for comfort in cold weather, while maintaining the DNA that Trane is known for: quality and reliability. The S9X1 is rated at up to 96% gas efficiency (AFUE), providing energy savings and a consistent flow of warm, comfortable air in both winter AND summer.

• Self-diagnostic integrated furnace control board (IFC)
• Matches with single- and two-stage AC and HP for more system options
• Sealed combustion, 100% outside air option
• Multi-port, in-shot burners
• Tubular, stainless steel primary heat exchanger
• Patented Vortica™ II blower design
• Pre-painted galvanized steel cabinet
• Fully insulated for quiet operation

Choose your speed Two-stage heat pumps use in two speeds to keep your home comfortable all year long. Our two-speed units provide an excellent mix of value, comfort, and efficiency.

• Spine Fin™ Coil
• WeatherGuard™ top

The S9X1 furnace offers a high-efficiency constant torque ECM blower motor for comfort in cold weather, while maintaining the DNA that Trane is known for: quality and reliability. The S9X1 is rated at up to 96% gas efficiency (AFUE), providing energy savings and a consistent flow of warm, comfortable air in both winter AND summer.

• Self-diagnostic integrated furnace control board (IFC)
• Matches with single- and two-stage AC and HP for more system options
• Sealed combustion, 100% outside air option
• Multi-port, in-shot burners
• Tubular, stainless steel primary heat exchanger
• Patented Vortica™ II blower design
• Pre-painted galvanized steel cabinet
• Fully insulated for quiet operation

The heating and cooling reliability you expect from Trane and the energy efficiency you deserve is available with these 2.5-ton to 5-ton heat pumps. The XR15 electric heat pump offers up to a 16.00 SEER rating when matched with Trane variable speed air handlers, furnaces and Comfort Coils™.

• Galvanized-steel louvered panels
• Baked-on powder paint
• Corrosion-resistant Weatherguard™ fasteners
• Spine Fin™ coil
• Sound insulator on compressor (on select models)

The S9V2-VS furnace is a high efficiency two stage furnace that achieves 97% gas efficiency (AFUE). It features both a variable speed draft inducer and our patented Vortica™ II variable speed blower motor, to bring you and your home comfort and efficient performance

• Variable-speed ECM blower motor
• Variable-speed draft inducer
• Comfort-R™ mode
• Single or two pipe vent options
• 40-120 mbth input
• Two-stage heat
• Fully insulated/gasketed
• Silicon nitride ignitor
• Standard 34″ height
• IFC boatd with digital configuration, status and fault codes
• Certified to 2% air leakage

The S9V2 furnace boasts an impressive 96% AFUE, making it one of the most efficient furnaces in the industry. Sit back, stay warm, and enjoy lower utility use in the winter and summer.

• Comfort-R™ mode
• Two-speed inducer
• Single or two pipe vent options
• 40–120 mbth input
• Two-stage heat
• Dry contact Humidifier and EAC terminals
• Fully insulated/gasketed
• Silicon nitride igniter
• Standard 34″ height
• IFC board with digital configuration, status and fault codes
• Certified to 2% air leakage

The S9X1 furnace offers a high-efficiency constant torque ECM blower motor for comfort in cold weather, while maintaining the DNA that Trane is known for: quality and reliability. The S9X1 is rated at up to 96% gas efficiency (AFUE), providing energy savings and a consistent flow of warm, comfortable air in both winter AND summer.

• Self-diagnostic integrated furnace control board (IFC)
• Matches with single- and two-stage AC and HP for more system options
• Sealed combustion, 100% outside air option
• Multi-port, in-shot burners
• Tubular, stainless steel primary heat exchanger
• Patented Vortica™ II blower design
• Pre-painted galvanized steel cabinet
• Fully insulated for quiet operation

The XL16c packaged heating and cooling system combines a high-efficiency air conditioner with a variable-speed gas furnace, maximizing your comfort from summer to winter and back. And it's all contained in one sleek cabinet.

• Ultra-quiet
• All stainless steel heating system
• Tough corrosion and UV-resistant paint
• Single and 3-phase
• Spine Fin™ condenser
• Comfort-R™ mode
• Composite Vortica™ blower
• Variable-speed indoor blower motor
• 2-stage gas heat

The XL15c gas/electric HVAC system delivers exceptional heating and cooling all while operating quietly and efficiently. With durable components assembled into one cabinet, this gas/electric HVAC system is designed to meet all of your home heating and cooling needs.

• 2-stage gas heat
• Variable-speed indoor blower motor
• Comfort-R™ mode
• Spine Fin™ condenser
• Ultra quiet
• Tough corrosion and UV-resistant paint
• Single phase only
• All stainless steel heating system

Stay comfortable with a stainless steel heating unit that doubles as an air conditioner.

• Composite Vortica™ blower will deliver the sustained performance you expect season after season
• All stainless steel heating system
• Tough corrosion and UV-resistant paint
• Single phase only

The XL16c EarthWise™ Hybrid heating systems allow you to choose the most efficient fuel source for the temperature situation in your home. The hybrid heating and cooling system combines a high-efficiency heat pump with a dual-stage furnace, and it's all contained in one sleek cabinet.

• Variable-speed indoor blower motor
• Spine Fin™ condenser
• Comfort-R™ mode
• Composite Vortica™ blower
• Single and 3-phase
• Heat pump and/or 2-stage gas heat operation
• All stainless steel heating system
• Ultra quiet

The XL14c EarthWise™ Hybrid heat pump gas furnace delivers exceptional heating, cooling and quiet operation. With the flexibility of two fuel sources, this packaged hybrid heat pump furnace lets you control the most efficient fuel to make your home comfortable

• Functional louvers with rounded corner guards for added safety
• All-aluminum Spine Fin™ coil
• Electric heat pump for mild conditions
• Increased dehumidification with Comfort-R™
• State-of-the-art fan system
• Heavy gauge, two-tone powder-painted cabinet
• Heat pump and/or 2-stage gas heat operation
• Stainless steel heat exchanger and burners

With Trane TruComfort™ variable speed technology, the XV20i continuously adjusts its speed to meet the temperature you desire. It gradually slows down or speeds up to deliver a consistent flow of cool, comfortable air.

• Compressor Sound Insulator
• Woven Spine Fin coil
• Variable-speed fan motor
• Swept fan blade
• ComfortLink II capability
• Simplified Two-Wire Connection

The 17.2 SEER2 rating makes this air conditioner energy-efficient while providing home comfort.

• Full-side louvered panels
• Spine Fin™ coil
• Swept fan blade

Two-stage cooling with the Trane XL16i offers flexible family comfort, with the ability to cool every room to the right temperature efficiently. So even the hard-to-cool parts of your home will be easy to relax in.

• Spine Fin™ coil
• Swept fan blade

The 14.8 SEER2 rating balances energy efficiency and cooling strength to help lower your home cooling costs.

• Spine Fin™ coil

More speeds, more comfort This system gives you comfort by running at the speed your home needs to stay comfortable. This allows the variable speed compressor, outdoor fan, and indoor fan to vary their speed as the temperature outside changes, slowing down or speeding up gradually when needed.

• Variable-speed fan motor
• Woven Spine Fin™ coil
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

One of the best on the market This heat pump is one of the industry’s most efficient systems, with ratings up to 18 SEER2 and 8.5 HSPF2. With Trane TruComfort™ technology, the XV18 automatically adjusts itself to keep you comfortable.

• Woven Spine Fin™ coil
• Variable-speed fan motor
• Swept fan blade
• Compressor sound insulator
• ComfortLink™ II capability
• Two-wire connections

Choose your speed Two-stage heat pumps use in two speeds to keep your home comfortable all year long. Our two-speed units provide an excellent mix of value, comfort, and efficiency.

• Spine Fin™ Coil
• WeatherGuard™ top

The heating and cooling reliability you expect from Trane and the energy efficiency you deserve is available with these 2.5-ton to 5-ton heat pumps. The XR15 electric heat pump offers up to a 16.00 SEER rating when matched with Trane variable speed air handlers, furnaces and Comfort Coils™.

• Galvanized-steel louvered panels
• Baked-on powder paint
• Corrosion-resistant Weatherguard™ fasteners
• Spine Fin™ coil
• Sound insulator on compressor (on select models)